At Carpetright we believe in making things easy for you at every step.
Whether you decide to use our professional Which? approved flooring fitters or want to take on the challenge of fitting your new carpet yourself, you will find everything you need in this fitting guide. We'll cover every step of the installation process including:
1: Draw a simple diagram of your home
It doesn’t have to be perfect but the measurements need to be accurate. Just a simple drawing with all the rooms shown is all you need.
If your room is perfectly square or rectangular, the area can be calculated by multiplying the width by the length. For example, a room that is 5m x 2m will need 10m2 of carpet.
2: Chimneys and recesses
If your room includes recesses or chimney breasts, you still need to measure the complete surface area without these as the carpet will be cut around them.
3: Getting the final figure
Measure each individual area and write the measurement in the relevant space on the diagram. Then break the room down into smaller rectangles that you can add together to get the total area of the room.
Remember to add 5% extra for waste.
4: Last checks
Measure your lengths more than once to confirm they’re right – just remember to measure the back of any door frames or room trims.
When it comes to stairs or steps, the process is similar. Measure the height and depth of each stair to give you the length before multiplying by the width. This will give you the area of each step. Again, don’t forget to allow 10% for waste and to allow for any margin of error as staircases can be tricky.
Watch our step-by-step video guides to measuring different room shapes from a simple room to a room with a join or extra space.
Watch our step-by-step guide to accurately measuring a simple room. It's never been easier to get a perfect fit.
Learn the basic steps to accurately measure a room with extra areas by watching our helpful video.
Accurately measure a room which requires a join by learning how from our step-by-step guide.
Like with measuring, getting the right kit to fit your carpet is another important consideration. Many of the tools you may already have in your toolbox and most DIY outlets will sell everything else. Tools you might need include:
• Knee pads
• Tape measure
• Masking tape
• Hammer or nail gun
• 19mm & 10mm nails
• 3mm hardboard sheets
• Pipe and cable detector
• Hack saw
• Carpet tape
• Craft or Stanley knife
• Carpet stretcher
• Carpet tucker
• Vacuum cleaner
Before you start fitting your new carpet you must prepare your sub-floor (a sub floor is the foundation for a floor in a building). If the sub-floor is not properly prepared it will affect the way that your carpet lies and potentially run the overall finish.
Before fitting your new carpet it’s likely that you will need to remove your old flooring alongside preparing the sub-floor underneath. At Carpetright we make fitting a new floor easy at every step. Alongside our professional Which? Approved fitting service, we can also uplift your old flooring and dispose of it for you to ensure that you experience a hassle-free fit.
• Always wear knee pads when working on flooring.
• If a lot of your floorboards are damaged, it’s cheaper and easier to pull them all up and start again. Use fit tongue-and-groove chipboard flooring panels which will give you a great base for your final flooring.
• 3mm hardboard sheets are best to level your boarded floor, plus they’ll help to reduce any draughts coming from below. Always make sure the boards have been conditioned beforehand by spraying them with water over the textured side and then stacking in the room in which they are going to be used back to back. Leave them for at least 48 hours and as they dry they’ll retract back. This reduces the risk of the boards expanding after they’ve been fitted.
• Prepare your boards by ensuring no nails are sticking out above the surface and nailing down any boards that are loose.
• Make sure you use 19mm nails to lessen the risk of piercing through the floorboard into pipes or cables.
• Space the nails about 150mm apart around the edges, but 225mm apart in the centre. It’s a good idea to start in the centre of one edge and work across the board to the other side.
• Lay the hardboard sheets texture-side up as you’ll need something for any adhesive to stick to. Start in a corner of the room and set the nails about 13mm in from the edges of the sheet in a pyramid pattern. It’s a good idea to use something as a spacer like a piece of wood.
• Push the sheets together and nail the edges where the sheets meet first. When you finish the first row of boards the last one will need to be cut to size.
• Use this off-cut from the last sheet in the first row to start the second row and carry on in the same way. This reduces waste and also helps by ensuring the joints are staggered.
Learn more about our uplift and disposal service.
Available in lengths of 1m, carpet gripper comes pre-nailed to provide a firm grip on your floors. These gripper rods are thick and rigid to provide an ultra-strong grip and keep the carpet taut, preventing any lumps and bumps. Simple to use, carpet gripper can be cut to size and can be used on concrete or wooden floors.
Before you start it is important to locate any hidden wires or pipes using a pipe and wire detector. If you find a pipe or wire, mark the spot in these areas and use gripper adhesive instead of nails. Make sure you wear gloves when handling gripper as the pins are very sharp. Gripper should be fitted all around the edge of your room except across door thresholds. Measure between the door frame and then cut the trim with a hack saw.
• For wooden floors use 10mm nails or screws.
• Place the gripper rods 2/3 of the carpet thickness away from the skirting boards with the pins pointing towards the skirting boards.
• Use a hacksaw to cut the gripper to size. Carpet gripper comes with nails or screws already in situ so hammer in the nails or screw in the screws.
• If the floor is concreted, use Gripfill and leave to dry.
• Follow the above instructions but use a bead of Gripfill under the gripper rods. This will help to maintain the integrity of the grippers if the nails work loose over time.
It’s worth investing in a good underlay as it’s really an integral element that shapes how flooring feels, wears and looks and will ensure your carpet has a long life. Underlay adds a level of cushioning underneath your carpet, making it more comfortable underfoot. It can also help to significantly reduce your energy bills as it insulates the room by trapping heat under your floor.
• Lay the underlay loosely in the space, ensuring the rubber side is facing down.
• Using a craft or Stanley knife cut it so that the underlay is at the same level as the grippers.
• Butt the edges together and join them with tape, ensuring that the edges do not overlap and that the underlay is flat and level.
Rather than an optional extra, underlay is an essential part of fitting a carpet correctly. It comes in many types, so if you’re not sure which one is right for your carpet, our Underlay Buying Guide will give you all the information on the different materials, the advantages of each and what their ratings mean.
And, when you’re ready to buy the materials for your subfloor, you can find everything you need for your job from carpet grippers to underlay.
In this section we show you how to lay a carpet and how to make sure you get the best overall finish.
Use a carpet stretcher (sometimes called a knee kicker) to stretch carpet onto the gripper. This tool has a flat plate with teeth at one end and a padded cushion at the other. The teeth grip the carpet while whoever fits the carpet pushes the padded end with their knee.
1: Lay your carpet loosely in position. Stand in one corner with a foot underneath the carpet. Use the other foot to smooth the carpet into place, leaving around 50-75mm excess on every edge. If necessary, cut the carpet to size.
2: Cut this excess vertically above the corners and trim the overlapping triangles.
3: Starting from the longest wall and working your way backwards, begin fitting the carpet. Use a carpet tucker to make a firm crease in the carpet along the skirting board. This will give you a fold line.
4: Using a sharp knife, cut along the edge, around 5mm higher than the carpet surface. Hold the carpet flat to the floor while you cut.
5: Take the carpet stretcher and place it around 25mm from the skirting, teeth facing down. Push the padded end firmly with your knee so the carpet hooks onto the gripper on either side of the corner.
6: Using the carpet tucker, push the excess carpet down between the skirting and the gripper. Repeat this process until the first wall is complete, then work along the two adjacent walls and finally the opposite one.
7: To fit carpet around tricky shapes such as door frames, cut down the edge vertically in several places, then trim it so it’s flush. For a pipe, cut straight from the carpet edge to the centre of the pipe then press the carpet around it. Trim it by running the knife round the base at a 45 degrees angle until the carpet lies flat.
8: For fitting carpet across a doorway, cut it so it is in line with the next room’s flooring. You will then need to then fit a door bar (see below) making sure the carpet edge is firmly in place underneath it.
Door bars serve to join different flooring types across door thresholds neatly. Read our top tips for how to fit your door bar correctly!
Unsure which door bar would finish off your carpet fitting best? Take a look at our selection of door bars and other accessories to find all the extras you’ll need for your room.
1: Make sure you have the right door bar depending on your flooring types and heights.
2: The correct position for a door bar is centrally across the threshold so it cannot be seen on either side when the door is closed. Once you have positioned your door bar centrally like this, cut the bar to the right length with a hack saw.
3: Check for pipes or cables under the floor by using a pipe and wire detector.
4: For a concrete floor, drill the holes with a power drill using a masonry bit and insert wall plugs. You can then fit your door bar.
5: For a wooden floor, make pilot holes first to ensure you have the right positioning before screwing the door bar to the floor.
Read our guide to buying flooring accessories for more information on getting the perfect finish.
In the days after fitting...
You may find that your carpets sheds some fibres which is perfectly normal. Regular vacuuming, daily if possible during the first few weeks, will solve this issue. A vacuum cleaner fitted with a beater bar and/or brushes is recommended for cut pile carpets and one without a beater bar or brushes is best for loop pile carpets.
Once the carpet is fitted, there may be a slight odour which may be caused by the carpet or the underlay. Ideally, the room should be ventilated by opening windows and doors and the odour will normally disappear within a few days.